Circular Bike Rack

Drawings & Downloads

NEED HELP? 888-661-0555 / M-F: 7AM - 4PM PACIFIC

The Sportworks Circular Rack combines the elements of high security with ease of use. This rack supports up to two bicycles at two different points on each bike allowing the wheel and the frame to be secured using a variety of lock types.

Made of heavy-duty mild or stainless steel, the Circular Rack is available with a variety of mounting, and coating options and is offered in 2" square tubing.

Finishes

Sportworks bike parking products are available in a wide variety of finishes and materials. Please contact us for specific details regarding minimum lot size charges on finishes.


TGIC Powder Coat

This polyester-based finish is well suited for bike racks made from mild steel, and is available in a wide variety of colors. Powder coating serves as a protective barrier to the various environment elements that cause corrosion. To further increase corrosion resistance, Sportworks recommends an additional zinc plated undercoat be applied prior to the powder coating process. Zinc acts as a sacrificial anode to protect the base metal from corrosion should the powder coat become chipped.

PPA-571 Thermoplastic Powder Coat

This thermoplastic finish is also well suited for mild steel racks, and Plascoat’s special formulation (PPA-571) produces a more flexible and robust coating. When compared to polyester-based powder coatings, PPA-571 thermoplastic powder coatings are tougher, more resistant to chips, and naturally graffiti resistant. This finish is also available in a wide variety of colors.

Galvanized

If color is not a requirement, this hot dip galvanized finish is a good choice for durability, low cost and corrosion protection on mild steel racks. While a galvanized finish will appear rough when compared to zinc plated and powder coated finishes, galvanizing provides the highest degree of corrosion resistance of all three. Additionally, galvanizing can also be used as an under coating treatment to TGIC and PPA powder coats. All Sportworks galvanized bike racks are finished to ASTM A123.

Bead Blast

Unlike powder coating and galvanizing, this finish removes material during the application process, and is ideal for stainless steel racks. Small glass particles (media) traveling at high velocities impact the metal removing the outer surface, and resulting in a mildly-textured or matted finish. Similar to galvanizing, there are no color options available for this type of finish. Sportworks stainless steel bike racks represent the highest level of corrosion protection available.

Materials


Mild Steel

The primary alloying element of mild steel is carbon. This enables bending and forming, while maintaining strong mechanical properties. A finish is required for outdoor applications (galvanizing, plating, powder coating, thermoplastics, or painting) as unfinished mild steel will rust and corrode when exposed to air and moisture.

Stainless Steel

Stainless steel does not stain, corrode, or rust as easily as mild steel because it contains more chromium and nickel. A passive film of oxides prevents surface corrosion and blocks corrosion from spreading into the internal structure of the metal. Stainless steel can still corrode and discolor in certain environments, however the strength and appearance can withstand exposure in most outdoor locations.

Powder Coat Colors

Sportworks offers the following standard color palette for our bicycle racks. All standard colors are available in both a polyester and a thermoplastic powder coat and are typically available within our standard lead time. All polyester powder coat colors include an epoxy primer undercoat. Zinc plating is also available as an alternate undercoat option.


Custom Colors

Custom colors are available, and subject to minimum orders and lot charges. Custom colors matching RAL or Pantone, as well as anti-graffiti powder coat colors are available and may involve extended lead times and/or lot changes. Plascoat thermoplastic powder coat provides the following benefits: excellent corrosion, fade, chip, abrasion and graffiti resistance. For more information regarding custom colors contact our sales team.


Mounting Options

Complete installation instructions for all Sportworks bike parking products are available as a PDF on this page or by visiting the downloads section of the website.


Surface Mount

Surface mount uses permanent or removable anchors to secure the bicycle rack mounting flange to concrete.

Mounting In Ground Mount

Embedding the bicycle rack into concrete represents the most secure mount for a bicycle rack. An additional 10” of length is included on the bicycle rack post(s) for casting in concrete.

Fastener Options


Concrete Wedge Anchor

Concrete Wedge Anchors, 3/8” Diameter x 3.75” Length, Stainless Steel, with 3/8-16 Hex Nut

Asphalt Anchor

Asphalt Anchor, 12” Length, Epoxy in Ground, Includes Epoxy, Hex Head Bolt 3/8”-16 x 2.5” Length and Washer

Tamper Resistant Anchors

Tamper resistant anchors are recommended for surface mounted racks. When the substrate is concrete, we recommend stainless steel wedge anchors with stainless steel breakaway nuts, also known as shear nuts. These nuts make it much more difficult for someone to tamper with or remove an installed bicycle rack.


Breakaway Nut Pre Installation

The breakaway nut consists of a hex nut portion at the top and a smooth conical sleeve located just below. Install the wedge anchor using standard tools and then tighten the breakaway nut.

Breakaway Nut Installed

The hex portion of the nut will shear off when the design shear torque is exceeded. Once the hex nut shears off, only the smooth conical sleeve will remain. The tamper resistant anchor is now installed. The cone is shaped so standard tools will not be able to grip and remove the nut.

Green Certifications

At Sportworks, we take environmental responsibility very seriously. Our bike racks are made with post-industrial recycled steel. We trace the location of origin and material/chemical composition of all the raw materials and sourced components we use. We also monitor VOC content in our finishing materials, and use recycled content in our packaging materials.

Installation of Sportworks bike racks may assist your project in qualifying for the following green building certification programs:

LEED®

  • SS Credit 4.2-Alternative Transportation-Bicycle Storage and Changing Rooms
    To qualify for this credit, commercial, institutional or residential buildings must provide secure bicycle parking within 200 yards of a building entrance.

  • MR Credit 4.1—Recycled Content—10% | MR Credit 4.2—Recycled Content—20%
    Sportworks stainless steel bicycle racks average 87% total recycled content; 72% post-consumer recycled content; 15% pre-consumer (post-industrial) recycled content.

  • MR Credit 5.1—Regional Materials—10% Extracted, Processed & Manufactured Regionally | MR Credit 5.2—Regional Materials—20% Extracted, Processed & Manufactured Regionally
    Our manufacturing facility is in Woodinville, Washington. If your project is within 500 miles of our factory, you may qualify for these credits.



Green Globes™

Sportworks bike racks can help you qualify for the following Green Globes™ credits:

  • E.2—Minimal Consumption of Resources
    Sportworks racks are made with recycled content and may be considered locally manufactured depending on the location of your project in relation to our factory in Woodinville, Washington.

  • C.5—Energy Efficient Transportation
    Sportworks racks support the requirement of providing safe storage areas with fixed mountings for bicycles.

Related Products

Heavy Duty Inverted-U Rack

The Heavy Duty Inverted-U is a full size rack that is available in heavy-duty mild or stainless steel, and comes in a variety of mounting and coating options.

Square Tube Inverted-U Narrow Rack

The Inverted-U Narrow Square Tube rack supports up to 2 bikes, and combines the elements of high security with ease of use.

Tofino™ No Scratch® Bike Rack

Modern and streamlined design with a No Scratch® bumper to keep bicycles damage-free. Optimal for indoor or outdoor use. Made in the USA of 87% recycled materials.